Short Description

Model No.: W.Nr.2.4600-Lap-Joint-Stub-End-Short-Pattern-1-1/4-Inch-Sch10S

China Lap Joint Stub End Manufacturer www.metallicsteel.com offers ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End, Short Pattern, 1-1/4 Inch, Sch10S.

Request a quoteShare

Key Specifications / Features

Type:W.Nr.2.4600 Lap Joint Stub End
Material: Hastelloy B3 (UNS N10675/W.Nr.2.4600)
Size: 1-1/4″ (DN32)
WT: Sch10S
Standard: ASME B16.9

20201026093716 77609 - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S

Chemical Composition of Hastelloy B3 (UNS N10675)

NiMoFeCCoCrMnSiTiWAlCu
65.0 min28.51.5.01 max3.0max1.53.0 max.10 max.2 max3.0 max.50 max.20 max

Equivalent Grades of Hastelloy B3 (UNS N10675)

酒店风云粤语版在线观看全集免费完整版第20集 雪梨影院,乙方甲方第二季MKV高清在线观看全集免费完整版第03集 雪梨 , 黑子的篮球第二季 全集在线观看 动漫 雪梨影院
TrademarksGBJISKSASTMUNSDINW.NrGOSTBSNF
Hastelloy B-3NS3203Hastelloy B-3N10675NiMo29Cr2.46

Physical Properties of Hastelloy B3 (UNS N10675)

Density
(g/cm3)

Melting Point
(℃)

Electric resistivity 
(µΩ·cm)

Coefficient of thermal expansion 
10-6K-1(20-100℃)

Elastic modulus
(GPa)

Hardness (Brinell)/HB

Operating temperature
(°C )

9.22

1418

137

10.6

216

94

 -200 – +400

Mechanical Properties of Hastelloy B3 (UNS N10675)

Annealed

  • Heat Treatment: 2100°F (1150°C)
  • Tensile Strength: 110 ksi (760 MPa) min 125 ksi (860 MPa) typ
  • Suggested Operating Conditions: -300°F to 1800°F (-184°C to 900°C)

lap joint stub end dimensions - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S

Lap Joint Stub End Metric Dimensions as per ASME B16.9

NPSODMaxODMinLPFSPFRG
1/2″0.8960.809320.121.38
3/41.1061.019320.121.69
11.3761.284420.122
1-/1/41.7161.629420.192.5
1-1/21.9651.869420.252.88
22.4562.34462.50.313.62
2-1/22.9662.84462.50.314.12
33.5963.46962.50.385
3-1/24.0963.969630.385.5
44.5934.469630.446.19
55.6835.532830.447.31
66.7436.59483.50.58.5
88.7438.594840.510.62
1010.91310.7191050.512.75
12酒店风云粤语版在线观看全集免费完整版第20集 雪梨影院,乙方甲方第二季MKV高清在线观看全集免费完整版第03集 雪梨 , 黑子的篮球第二季 全集在线观看 动漫 雪梨影院12.91312.7191060.515
NPSODMaxODMinLPFSPFRG
1414.1713.9691260.516.25
1616.1815.9691260.518.5
1818.1917.969126酒店风云粤语版在线观看全集免费完整版第20集 雪梨影院,乙方甲方第二季MKV高清在线观看全集免费完整版第03集 雪梨 , 黑子的篮球第二季 全集在线观看 动漫 雪梨影院0.521
2020.2419.9691260.523
2222.2421.9691260.525.25
2424.2423.9691260.527.25

GENERAL NOTES:

  • (a) All dimensions are in millimeters.
  • (b) See Table 1 for tolerances.
  • (c) Service conditions and joint construction often dictate stub end length requirements. Therefore, the purchaser must specify long or short pattern fitting when ordering.

NOTES:

  • (1) Gasket face finish shall be in accordance with ASME B16.5 for raised face flanges.
  • (2) The lap thickness T shall not be less than nominal pipe wall thickness. See Table 1 for maximum tolerance.
  • (3) When short pattern stub ends are used with larger flanges in Classes 300 and 600, with most sizes in Classes 900 and higher, and when long pattern stub ends are used with larger flanges in Classes 1500 and 2500, it may be necessary to increase the length of the stub ends in order to avoid covering the weld with the flange. Such increases in length shall be a matter of agreement between the manufacturer and purchaser.
  • (4) When special facings such as tongue and groove, male and female, etc., are employed, additional lap thickness must be provided and such additional thickness shall be in addition to (not included in) the basic length F.
  • (5) These dimensions conform to the radius established for lap joint flanges in ASME B16.5.
  • (6) This dimension conforms to standard machined facings shown in ASME B16.5. The back face of the lap shall be machined to conform to the surface on which it seats. Where ring joint facings are to be applied, use dimension K as given in ASME B16.5.

Dimensional Tolerances of Stub Ends ASME B16.9 (Table.1)

Nominal Pipe Size1/2 up to 2½3 to 3½45 to 810 to 1820 to 24
Outside Diameter at Welding End (OD)
+ 1.6
– 0.8
1.61.6
+ 2.29
– 1.6
+ 4.06
– 3.05
+ 6.35
– 4.83
Overall Length (F)1.61.61.61.622
Outside Diameter of Lap (G)
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 1.6
+ 0
– 1.6
Thickness of Lap (T)
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
+ 1.52
– 0
Fillet Radius of Lap (R)
+ 0
– 0.76
+ 0
– 0.76
+ 0
– 1.6
+ 0
– 1.6
+ 0
– 1.6
+ 0
– 1.6
Wall Thickness (t)Not less than 87.5% of Nominal Wall Thickness酒店风云粤语版在线观看全集免费完整版第20集 雪梨影院,乙方甲方第二季MKV高清在线观看全集免费完整版第03集 雪梨 , 黑子的篮球第二季 全集在线观看 动漫 雪梨影院

  • Dimensional tolerances are in millimeters unless otherwise indicated.

Summary
asme b16 9 astm b366 w nr 2 4600 lap joint stub end short pattern 1 1 4 inch sch10s - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S
Author Rating
1star - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S1star - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S1star - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S1star - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S1star - ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S
Aggregate Rating
5 based on 1votes
Brand Name
Yaang
Name
ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S
USD1-9999
Product Availability
Pre-Order Only

Request a quote

    Subject:

    Products Related to ASME B16.9 ASTM B366 W.Nr.2.4600 Lap Joint Stub End Short Pattern 1-1/4 Inch Sch10S